View DS1819_171078.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DS1814/DS1819 5V and 3.3V MicroMonitor
www.maxim-ic.com
FEATURES
Halts and restarts an out-of-control microprocessor Holds microprocessor in check during power transients Automatically restarts microprocessor after power failure Monitors pushbutton for external override Accurate 5%, 10%, or 20% (3V only) microprocessor power monitoring Eliminates the need for discrete components 20% tolerance for use with 3.0V systems Pin- and function-compatible with the MAX823/24/25 products Low cost SOT-23-5 package Industrial temperature range: -40C to +85C
RST
PIN ASSIGNMENT
3 2 1
4
5
SOT-23-5 PACKAGE See Mech. Drawing
PIN DESCRIPTION
DS181xA 1 RST 2 GND PBRST 3 4 ST 5 VCC DS181xB 1 RST 2 GND 3 RST 4 ST 5 VCC DS181xC 1 RST 2 GND 3 RST 4 PBRST 5 VCC Active Low Reset Output Ground Pushbutton Reset Input Strobe Input Power Supply
DEVICE
RST
PBRST
WD X X
DS181xA X DS181xB X X DS181xC X X x = "DS1814" for 5V devices x = "DS1819" for 3V devices
X X
Active Low Reset Output Ground Active High Reset Output Strobe Input Power Supply
Active Low Reset Output Ground Active High Reset Output Pushbutton Reset Input Power Supply
DESCRIPTION
The DS1814 5-Volt MicroMonitor and the DS1819 3.3V MicroMonitor monitor three vital conditions for a microprocessor: power supply, software execution, and external override. First, a precision temperaturecompensated reference and comparator circuit monitor the status of VCC. When an out-of-tolerance condition occurs, an internal power-fail signal is generated which forces the reset(s) to an active state. When VCC returns to an in-tolerance condition, the reset signal is kept in the active state for a minimum of 140ms to allow the power supply and processor to stabilize.
1 of 8 122001
DS1814/DS1819
The DS1814/DS1819 `A' and `C' perform pushbutton reset control. They debounce the pushbutton input and generate an active reset pulse width of 140ms minimum. The DS1814/9 `A' and `B' versions perform a watchdog function. The watchdog is an internal timer that forces the reset signals to the active state if the strobe input does not change state every 1.12 seconds. The watchdog timer function can be disabled by leaving the watchdog strobe input disconnected.
OPERATION Power Monitor
The DS1814 detects out-of-tolerance power supply conditions and warns a processor-based system of impending power failure. When VCC falls below a preset level, a comparator outputs the signal RST (or RST). RST (or RST) are excellent control signals for a microprocessor, as processing is stopped at the last possible moment of valid VCC. On power-up, RST (or RST) are kept active for a minimum of 140ms to allow the power supply and processor to stabilize.
Pushbutton Reset
The DS1814 `A' and `C' provide an input pin for direct connection to a pushbutton reset (see Figure 2). The pushbutton reset input requires an active low signal. Internally, this input is debounced and timed such that a RST (or RST) signal of at least 140ms minimum will be generated. The 140ms delay commences as the pushbutton reset input is released from the low level (see Figure 3).
Watchdog Timer
The DS1814/DS1819 `A' and `B' versions watchdog timer function forces RST (and RST) signal(s) active when the ST input is not clocked within the 1.12 second watchdog time-out period. Time-out of the watchdog starts when RST (and RST) become(s) inactive. If a transition occurs on the ST input pin prior to time-out, the watchdog timer is reset and begins to time out again. If the watchdog timer is allowed to time out, then the reset output(s) will go active for 140ms. The watchdog can be disabled by floating (or tri-stating) the ST input. The ST input can be derived from many microprocessor outputs. The most typical signals used are the microprocessor data I/O signals and control signals. When the microprocessor functions normally, these signals would as a matter of routine cause the watchdog to be reset prior to time-out. To guarantee that the watchdog timer does not time out, a transition must occur at or less than 1.12 seconds. A typical circuit example is shown in Figure 4. The DS1814/19 watchdog function can be disabled at any time by tri-starting the strobe input. A sample circuit to disable the watchdog is shown in Figure 6.
2 of 8
DS1814/DS1819
DS1814/DS1819 BLOCK DIAGRAM Figure 1
*Notes: ST available on'A' and 'B' versions PBRST available on 'A' and 'C' versions RST available on 'B' and 'C' versions
PUSHBUTTON RESET Figure 2
TIMING DIAGRAM: PUSHBUTTON RESET Figure 3
3 of 8
DS1814/DS1819
WATCHDOG TIMER Figure 4
TIMING DIAGRAM: STROBE INPUT Figure 5
WATCHDOG DISABLE CIRCUIT Figure 6
TIMING DIAGRAM: POWER-DOWN Figure 7
4 of 8
DS1814/DS1819
TIMING DIAGRAM: POWER-UP Figure 8
RST VALID TO 0 VOLTS VCC Figure 9
OUTPUT VALID CONDITIONS
The RST output uses a push-pull output which can maintain a valid output down to 1.0V VCC. To sink current below 1.0V a resistor can be connected form RST to Ground (see Figure 9.) This arrangement will maintain a valid value on RST during both power-up and -down but will draw current when RST is in the high state. A value of about 100kW should be adequate in most situations. The output with a resistor pull-down can maintain a valid reset down to VCC equal to 0V.
5 of 8
DS1814/DS1819
ABSOLUTE MAXIMUM RATINGS*
Voltage on VCC Pin Relative to Ground Voltage on I/O Relative to Ground Operating Temperature Range Storage Temperature Range Soldering Temperature * -0.5V to +7.0V -0.5V to VCC + 0.5V -40C to +85C -55C to +125C 260C for 10 seconds
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
PARAMETER Supply Voltage
ST and PBRST Input High Level ST and PBRST Input Low Level
(-40C to +85C)
TYP MAX 5.5 0.3 VCC UNITS V V V NOTES 1 1 1
SYMBOL VCC VIH VIL
MIN 1.0 0.8 VCC
DC ELECTRICAL CHARACTERISTICS
PARAMETER VCC Trip Point DS1814-5 VCC Trip Point DS1814-10 VCC Trip Point DS1819-5 VCC Trip Point DS1819-10 VCC Trip Point DS1819-20 Reset Trip Point Hysteresis (DS1814) Reset Trip Point Hysteresis (DS1819) Output Current @ 2.4V Output Current @ 0.4V Output Voltage @ -30 mA Operating Current DS1814 Operating Current DS1819
ST Input Current ST = VCC, Time Averaged ST Input Current ST = GND, Time Averaged
(-40C to +85C; VCC = 1.2V to 5.5V)
MIN 4.50 4.25 3.00 2.85 2.55 10 5 350 3.2 VCC*.8 6 VCC*.9 10 8 120 -20 -15 15 12 160 TYP MAX 4.75 4.50 3.15 3.00 2.70 UNITS V V V V V mV mV mA mA V mA mA mA mA 3 3 3 4 5 6 6 NOTES 1 1 1 1 1
SYMBOL VCCTP VCCTP VCCTP VCCTP VCCTP VRH VRH IOH IOL VOH ICC ICC
6 of 8
DS1814/DS1819
AC ELECTRICAL CHARACTERISTICS
PARAMETER
PBRST = VIL
(-40C to +85C; VCC = 1.2V to 5.5V)
MIN 1 140 50 1.12 1.60 30 12.5 140 200 500 2.40 40 280 TYP 200 MAX 280 UNITS ms ms ns s ms V/ms ms ns 9 8 NOTES 7
SYMBOL tPB tRST tST tTD tRPD tRPU tPDLY
Reset Active Time
ST Pulse Width
Watchdog Time-out VCC Detect to RST and RST VCC Slew Rate (rising edge) VCC Detect to RST and RST
PBRST Stable Low to RST and RST
CAPACITANCE
PARAMETER Input Capacitance Output Capacitance SYMBOL CIN COUT MIN TYP MAX 5 7
(tA = 25C)
UNITS pF pF NOTES
NOTES:
1) All voltages are referenced to ground. 2) PBRST is internally pulled up to VCC with an internal impedance of 50kW typical. 3) Measured with VCC 2.7V. 4) Measured with outputs open, VCC 5.5V, and all inputs at VCC or Ground, except the ST input at <10kHz duty cycle-square wave or ST input open. 5) Measured with outputs open, VCC 3.6V, and all inputs at VCC or Ground, except the ST input at <10kHz duty cycle-square wave or ST input open. 6) The ST input current is defined as the average input current when ST is driven high or low. This input must be driven high or low by an output that can source or sink at least 200mA when active. 7) Noise immunity: pulses <100ns at pushbutton input will not cause a reset. 8) Must not exceed tTD minimum. 9) Noise immunity: pulses <2ms at VCCTP minimum will not cause a reset and VCCTP - VCC = 100mV.
7 of 8
DS1814/DS1819
PART MARKING CODES
SOT-23-5 PACKAGE
`A', `B' and `C' represents the Device Type. 14A 14B 14C 19A 19B 19C DS1814A DS1814B DS1814C DS1819A DS1819B DS1819C
`D' represents the Device Tolerance. A B C 5% 10% 20%
8 of 8

▲Up To Search▲

Price & Availability of DS1819

	To Download DS1819 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .